The Two15 frameset is your chance to set up a piece of World Cup-tested high-end kit to your own specifications. This is a genuine race replica so, of course, we finished it in our Global Squad design.

Znajdź sprzedawcę
  • zastosowanie: Gravity
  • materiał ramy: Aluminium
  • rozmiar: S / 27.5, M / 27.5, L / 29, XL / 29
  • Art. No: 258300

Komponenty

  • rama HPA Ultralight, Advanced Hydroform, Triple Butted, ETC 4-Link, ISCG Mount, 215mm travel (29": 200mm)
  • rozmiar S / 27.5, M / 27.5, L / 29, XL / 29
  • kolor globalsquad
  • damper Fox Float X2 Factory, 240x76mm, High/Low Speed Rebound & Compression, Kashima Coated
  • siodło SDG FLY 2.0 I-Beam
  • sztyca podsiodłowa SDG I-Beam Carbon, 31.6mm
  • zacisk sztycy CUBE Screwlock, 34.9mm
  • dodatki Syntace 157mm X12 Axle
  • tuleje dampera Top: 30x8mm, Bottom: 22x8mm
  • waga 4,8 kg

Geometria

Geometry Seat Tube Top Tube Horizontal Seat Tube Angle Head Tube Angle Chain Stays Head Tube Wheelsbase BB-Height<br> to Hub Rear Travel Reach Stack Wheelsize
  • Info
  • S
  • M
  • L
  • XL

Szczegóły

The principle behind the Two15's frame design is the same successful four pivot concept that powers all our full suspension bikes. That's important, because it means that we were able to realise the same suspension characteristics as our super-efficient trail bikes, but with plenty of rear wheel travel and noticeably better agility and control than simpler DH bike designs. But we didn't stop with the kinematics - our engineers also put a lot of effort into reducing weight. The Two15's hydroformed, triple butted tubeset with 157mm rear hub spacing weighs only a little more than an enduro frame, but delivers extaordinary steering precision and epic rock swallowing ability. Our optimised suspension design provides apparently endless grip on every trail surface, and the internal cable routing keeps gear shifts clean and the the frame's looks cleaner still.

Image of 6
Kategoria klasyfikacji rowerów: 6
Więcej na temat klasyfikacji

Pozostałe modele z serii

 

Cross Country

Tour/Trail

All Mountain

Enduro

Gravity

Technologie

  • Icon of CUBE technology Adaptable X12 Hanger
      • Adaptable X12 Hanger
      • Adaptable X12 Hanger

        We optimized our new dropout design based on the Syntace X12 through-axle system, enlarging the area of the frame where the hanger is mounted. We can now fit the longer Direct Mount hangers. Shifting precision and stiffness is therefore improved. With the new design it's also possible to swap the whole contact area of the axle with the hanger should the system be worn out.

  • Icon of CUBE technology FOX Customized Setup
      • FOX Customized Setup
      • FOX Customized Setup

        Sophisticated suspension kinematics are only able to work correctly if the associated shock is properly tuned. We researched and found a specific shock setup in cooperation with Fox Racing Shox, using extensive testing for almost every CUBE full-suspension model.

  • Icon of CUBE technology Integrated Post Mount
      • Integrated Post Mount
      • Integrated Post Mount

        The post mount rear brake system is found on all carbon fiber frames and top aluminum full suspension models. Two bolts and the IS adpater aren’t needed anymore, and fewer parts means less weight. In this case we save 30 grams. This may not sound a lot. But there's potential to save weight in every detail.

  • Icon of CUBE technology Integrated Cable Routing
      • Integrated Cable Routing
      • Integrated Cable Routing

        Internally routed cables offer many advantages. Cables are protected from dirt for longer life, weight is saved thanks to the absence of external housing and the bike has a clean, sleek appearance.

  • Icon of CUBE technology X12 Through Axle
      • X12 Through Axle
      • X12 Through Axle

        In this system, a cone is used to form a play-free connection. It is only necessary to tighten the axle from one side. The position of the wheel is done by an insert in the right-hand dropout which is secured by a bolt. The main advantages of the Syntace system are quick and simple changing of the wheel, reliable position of the brake disc and higher stiffness of the rear of the bike. This allows the assembly to be made lighter than a conventional through-axle.

  • Icon of CUBE technology Press Fit BB
      • Press Fit BB
      • Press Fit BB

        With Press Fit bearings, the bottom bracket bearings are pressed directly into the frame and not screwed in as usual. This gives a wider bottom bracket shell and allows us to build a wider down tube and more broadly-spaced chainstays. Every millimetre of additional width gives a significant improvement in lateral stiffness.

  • Icon of CUBE technology Wet Paint Surface
      • Wet Paint Surface
      • Wet Paint Surface

        On polished, brushed aluminium and all HPC frames, the logos and graphics are applied in multi-layer wet paint. We use this surface treatment technology mainly to save weight.

  • Icon of CUBE technology FSP4Link
      • FSP4Link
      • FSP4Link

        The key requirement is for continuously active and fully usable travel, with the rear triangle unaffected by pedalling or especially braking forces. There are a number of ways of achieving this – CUBE favours a four bar design with a chainstay pivot. Here, one of the pivots is located between the dropout and the chainstay, ensuring that braking does not have a negative effect on the movement of the rear wheel. By carefully positioning the remaining pivots, we obtain the finest riding qualities for our full suspension bikes both uphill and downhill. This fact is proven by many top test results in leading magazines over the last few years.

  • Icon of CUBE technology Aluminium Superlite
      • Aluminium Superlite
      • Aluminium Superlite

        Extremely high tensile strength heat-treated 7005 aluminium alloy is developed for the highest requirements. It is very stiff, fatigue resistant, corrosion resistant and has high elongation. Our Superlite tubes are double butted, giving very light tubesets with a high level of stiffness.

  • Icon of CUBE technology Advanced Hydroforming
      • Advanced Hydroforming
      • Advanced Hydroforming

        The new STEREO , FRITZZ and HANZZ models are built using Advanced Hydroforming. Conventional hydroforming processes cannot achieve these custom shapes and technical advantages. As this manufacturing method reduces the number of welds, the weight is reduced while durability is increased. All

  • Icon of CUBE technology High Performance Aluminium
      • High Performance Aluminium
      • High Performance Aluminium

        For our high end bikes we use High Performance 7005 Aluminium alloy which has a very low density combined with high strength due to the alloy elements and the hardening heat treatment. By triple butting or even quadruple butting (as in the REACTION , HANZZ and AERIUM models) to give different wall thicknesses in one tube, aluminium tubes are reinforced where required and made lighter where possible. In this way, we succeed in getting material where its needed most. In addition we use special tube shapes, manufactured with hydroforming technology to better cope with directional forces. The low density and high strength as well as the butting and the hydroforming technology enable us to make high performance frames with an ultimate level of stiffness.

Gdzie kupić

CUBE TWO15 FRAMESET

Aby uzyskać szczegółowe informacje na temat ceny roweru, skontaktuj się z wybranym sprzedawcą, lub przejdź do naszego sklepu online

Szukaj sprzedawcy